Amana Tool DRB-450 Polycrystalline Diamond (PCD) Tipped Double Edge Folding V-Groove 90 Deg. x 0.090 Tip Cut Width x 1/2 D x 3/8 CH x 1/4 SHK x 2 Inch Long Router Bit

Amana Tool® Item #DRB-450
$206.40
$185.76
Free shipping on orders $49 and up

Double Edge Folding PCD V-Groove Router Bits for Shaping Aluminum Composite Material (ACM) Panels

These bits are widely used as cladding for many diverse applications such as office buildings, hospitals, convention centers, airports, hotels. Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding/creasing the remaining material by hand.

Designed for scoring Aluminum Composite Materials including:

  • Acetate
  • Aluminum, Brass, Bronze, Clay, Zinc & Wood Composite Panels
  • Aluminum Composite Materials (ACM)
  • Aluminum Composite Panel (ACP)*
  • ALPOLIC® Copper Composite Material (CCM)
  • Alucobond®
  • Alupanel®
  • Bakelite
  • Dibond®
  • Durabond**
  • e-panel™
  • Etalbond®
  • PE and FR Cores
  • Phenolics
  • Plastic/Acrylic
  • Plexiglas®
  • PVC
  • Thermoplastics
  • Titanium Composite Material (TCM)
  • Wood



Diamond Technology

Diamond is the hardest material on the earth. Polycrystalline Diamond (PCD) tooling is manufactured in a high-temperature and high-pressure laboratory that fuses diamond particles onto a carbide substrate, which allows the diamond to be brazed onto a tool body.

PCD Tooling Benefits:



  • Harder cutting edge provides higher resistance to wear
  • Cut thousands of feet more than carbide without changing tool, saving setup time
  • Optimized machine tool efficiency
  • Quality of finish is often significantly improved
If you’re looking for the ultimate in tooling, you’ve found it! Amana Tool®'s PCD tipped Double Edge Folding V-Groove router for shaping Aluminum Composite Material (ACM) panels bits will cut, score and groove a wide variety of tough, abrasive materials including composites, Aluminum, MDF (both raw or with melamine), Fiberglass and hardwoods. The cutting edge lasts much longer than carbide for extremely long life. Depending on the material being cut, PCD tooling has been known to out perform a carbide tool by a ratio of 300:1. However, to be conservative in your buying decision, we suggest you base your expectations on 25:1 ratio over carbide tooling.

Excellent for scoring:

  • Composite panels
  • Custom composite materials
  • Fiberglass
  • Fiberglass PCB board
  • Fiber-reinforced urethane
  • Fiber-reinforced structural foam floors
  • Lightweight composites
  • MDF
  • Plywood
  • Plastic
  • Hard and soft wood

*Aluminum Composite Panel (ACP) is a type of ACM flat panel that consists of two thin aluminium sheets bonded to a non-aluminium core and is widely used as cladding for many diverse applications such as interior and exterior office buildings, external cladding or facades of buildings, hospitals, convention centers, airports, hotels, insulation and signage. **Durabond is a polyethylene core with 0.3mm colored aluminum sheet on either side, pre-finished requiring no decoration. Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding the remaining material by hand. Ideal for wall panel fabrication.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2021 Toolstoday. All rights reserved.