Aluminum Composite Panel (ACP) is a type of ACM flat panel that consists of two thin aluminium sheets bonded to a non-aluminium core and is widely used as cladding for many diverse applications such as interior and exterior office buildings, external cladding or facades of buildings, hospitals, convention centers, airports, hotels, insulation and signage. **Durabond is a polyethylene core with 0.3mm colored aluminum sheet on either side, pre-finished requiring no decoration.
Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding the remaining material by hand.
Specially designed router bits are used to route V-grooves in the above materials to allow easy bending without cracking the bent area. Route within 0.8mm from the bottom of the composite panel to achieve a clean bend/radius. Routing V-shaped grooves, whereby the aluminum cover and a part of the polyethylene core is removed, allows folding the remaining material by hand. Ideal for wall panel fabrication.
Amana Tool AMS-140 3-Pc Carbide Tipped V-Groove 90, 108 and 135 Deg. for Double Edge Folding Aluminum Composite Material (ACM) Panels, 1/4 Inch SHK Router Bit Collection
Amana Tool® Item #AMS-140
$207.10
$155.33
Free shipping on orders $49 and up
Carbide tipped double edge folding 'V’ groove & rectangular groove (for thicker walls) industrial router bits for shaping Aluminum Composite Materials (ACM) such as Alucobond®, Dibond® and other brands alike. Designed for scoring the following aluminum/plastic composite materials with 90°, 108°, 135° angles (with flat bottoms) and rectangular grooves:
- Acetate
- Acrylonitrile-Butadiene-Styrene (ABS)
- Aluminum, Brass, Bronze, Clay, Zinc & Wood Composite Panels
- Aluminum 5052
- Aluminium Composite Materials (ACM)
- Aluminium Composite Panel (ACP)*
- ALPOLIC® Copper Composite Material (CCM)
- Alcubond®
- Alupanel®
- Bakelite
- Dibond®
- Durabond**
- e-panel™
- Etalbond®
- Lexan™
- Nylon
- PE and FR Cores
- Phenolics
- Plastic/Acrylic
- Plexiglas®
- PVC
- Stainless Steel Composite Material (SCM)
- Titanium Composite Material (TCM)
- Wood
- For use on routers and CNC machines
- Industrial quality, carbide tipped
- ACM panels may be used both indoors and outdoors. Ideal for wall panel fabrication
- RPM: 18,000-24,000 (*Feed rate should be 120 inches per minute.)
Benefits of ZrN Coating:
- Optimized flute geometry and low Total Indicated Runout (TIR) guarantees clean cuts, essentially eliminates sanding and reduces chatter when used with low TIR spindles
- Creates a harder and tougher cutting ceramic over carbide edge, allowing for a prolonged cutting edge life and helps to prevent the build-up/galling of material in the flutes while cutting
- Has the ability to run and/or be spun much faster than uncoated tools
- High aspect ratio for single pass deep-reach cutting
- High flute volume supports high feed rates and chip loads.
- Flute geometry optimized for cutting sign foam, sign board, hardwoods, thermoplastics and phenolic composites
Tool No.
CNC Feed/Speed
Vectric .tool & Fusion .tools File
AutoCad PDF/DXF File
Set #AMS-140 Includes the Following Tools:
Tool No
Description
Product Page
45792
90º x 0.090" Tip x 1/2" Dia x 1/4 Shank V-Groove Double Edge Folding for ACM Router Bits
45795
108º x 0.090" Tip x 1/2" Dia x 1/4 Shank V-Groove Double Edge Folding for ACM Router Bits
45798
135º x 0.080" Tip x 23/32" Dia x 1/4 Shank V-Groove Double Edge Folding for ACM Router Bits
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.