Carbide Tipped Through-Hole (V Point) Boring Bits - 57mm Long - 10mm x 25mm Shank-Right Hand

Priced From
$17.15
-
$29.05
Free shipping on orders $49 and up
SEE OPTIONS BELOW
BUY 5 OF THE SAME SAVE 5%
Discount applied in your shopping cart
BUY 10 OF THE SAME SAVE 10%
Discount applied in your shopping cart
*Sort the Table by clicking on the Column Heading
dLDiameterBRotationBrandTool NoOur PriceWish ListReady To Buy
10mm57mm4mm35mmRight Hand
Amana Tool 313004 Carbide Tipped Through-Hole Boring Bit R/H 4mm D x 57mm Long x 10mm SHKMore infoAmana Tool313004$27.15$19.01
Qty:
10mm57mm5mm35mmRight Hand
Amana Tool 313005 Carbide Tipped Through-Hole Boring Bit R/H 5mm D x 57mm Long x 10mm SHKMore infoAmana Tool313005$28.85$20.20
Qty:
10mm57mm6mm35mmRight Hand
Amana Tool 313006 Carbide Tipped Through-Hole Boring Bit R/H 6mm D x 57mm Long x 10mm SHKMore infoAmana Tool313006$33.05$23.14
Qty:
10mm57mm1/435mmRight Hand
Amana Tool 313007 Carbide Tipped Through-Hole Boring Bit R/H 1/4 D x 57mm Long x 10mm SHKMore infoAmana Tool313007$34.50$24.15
Qty:
10mm57mm7mm35mmRight Hand
Amana Tool 313070 Carbide Tipped Through-Hole Boring Bit R/H 7mm D 58mm Long x 10mm SHKMore infoAmana Tool313070$36.65$25.66
Qty:
10mm57mm8mm35mmRight Hand
Amana Tool 313008 Carbide Tipped Through-Hole Boring Bit R/H 8mm D x 57mm Long x 10mm SHKMore infoAmana Tool313008$27.25$19.08
Qty:
10mm57mm9mm35mmRight Hand
Amana Tool 313090 Carbide Tipped Through-Hole Boring Bit R/H 9mm D x 58mm Long x 10mm SHKMore infoAmana Tool313090$31.45$22.02
Qty:
10mm57mm3/835mmRight Hand
Amana Tool 313009 Carbide Tipped Through-Hole Boring Bit R/H 3/8 D x 57mm Long x 10mm SHKMore infoAmana Tool313009$43.40$30.38
Qty:
10mm57mm10mm35mmRight Hand
Amana Tool 313010 Carbide Tipped Through-Hole Boring Bit R/H 10mm D x 57mm Long x 10mm SHKMore infoAmana Tool313010$41.50$29.05
Qty:
Note: Right hand tools rotate clockwise. Left hand tools rotate counter-clockwise.
Industrial Through-Hole Boring Bits are Coated with a Non-Stick Coating for Longer Lasting Cutting Edge and Tool Life. 
Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. 

Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.
 
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2020 Toolstoday. All rights reserved.