Carbide Tipped Brad Point Boring Bits - 77mm Long - 10mm x 30mm Shank-Left Hand

Priced From
$17.29
-
$31.01
Free shipping on orders $49 and up
SEE OPTIONS BELOW
BUY 5 OF THE SAME SAVE 5%
Discount applied in your shopping cart
BUY 10 OF THE SAME SAVE 10%
Discount applied in your shopping cart
*Sort the Table by clicking on the Column Heading
dLDiameterBRotationBrandTool NoOur PriceWish ListReady To Buy
10mm77mm4mm44mmLeft Hand
Amana Tool 302004 Carbide Tipped Brad Point Boring Bit L/H 4mm D x 77mm Long x 10mm SHKMore infoAmana Tool302004$24.70$17.29
Qty:
10mm77mm5mm44mmLeft Hand
Amana Tool 302005 Carbide Tipped Brad Point Boring Bit L/H 5mm D x 77mm Long x 10mm SHKMore infoAmana Tool302005$31.65$22.16
Qty:
10mm77mm5.1mm44mmLeft Hand
Amana Tool 302051 Carbide Tipped Brad Point Boring Bit L/H 5.1mm D x 77mm Long x 10mm SHKMore infoAmana Tool302051$37.70$26.39
Qty:
10mm77mm8mm44mmLeft Hand
Amana Tool 302008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 77mm Long x 10mm SHKMore infoAmana Tool302008$33.05$23.14
Qty:
10mm77mm8.2mm44mmLeft Hand
Amana Tool 302082 Carbide Tipped Brad Point Boring Bit L/H 8.2mm D x 77mm Long x 10mm SHKMore infoAmana Tool302082$40.85$28.60
Qty:
10mm77mm9mm44mmLeft Hand
Amana Tool 302090 Carbide Tipped Brad Point Boring Bit L/H 9mm D x 77mm Long x 10mm SHKMore infoAmana Tool302090$38.85$27.20
Qty:
10mm77mm10mm44mmLeft Hand
Amana Tool 302100 Carbide Tipped Brad Point Boring Bit L/H 10mm D x 77mm Long x 10mm SHKMore infoAmana Tool302100$40.15$28.11
Qty:
10mm77mm12mm44mmLeft Hand
Amana Tool 302012 Carbide Tipped Brad Point Boring Bit L/H 12mm D x 77mm Long x 10mm SHKMore infoAmana Tool302012$44.30$31.01
Qty:
Note:
#302006 is replaced by #302070
Industrial Brad Point Boring Bits are Coated with a Non-Stick Coating for Longer Lasting Cutting Edge and Tool Life. 
Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. 

Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.
 
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2020 Toolstoday. All rights reserved.