Bevel Trim Router Bits-2 Flute

Priced From
$22.91
-
$28.61
Free shipping on orders $49 and up
SEE OPTIONS BELOW
$30.55
$22.91
BUY 5 OF THE SAME SAVE 10%
Discount applied in your shopping cart
*Sort the Table by clicking on the Column Heading
DD1Bdd1LFluteBall BearingReplacement BearingCBrandTool NoOur PriceWish ListReady To Buy
1/43/163/81/43/161-7/82Lower47706-
Amana Tool MR0106 Miniature 7 Degree Chamfer with 3/16 D Ball Bearing x 1/4 D x 3/8 CH x 1/4 Inch SHK Carbide Tipped Router BitMore infoAmana ToolMR0106$36.10$27.08
Qty:
15°5/8-1/41/4-2-3/322Lower47706-
Amana Tool 47200 Carbide Tipped Bevel Laminate Trim 15 Deg Angle x 5/8 D x 9/32 CH x 1/4 Inch SHK w/ Ball Bearing Router BitMore infoAmana Tool47200$30.55$22.91
Qty:
22°1/2-5/161/4-1-3/42Lower47723-
Amana Tool 47201 Carbide Tipped Bevel Laminate Trim 22 Deg Angle x 1/2 D x 3/8 CH x 1/4 Inch SHK w/ Ball Bearing Router BitMore infoAmana Tool47201$33.10$24.83
Qty:
22-1/2°1/23/161/21/43/161-7/82Lower477067/8
Amana Tool MR0107 Miniature 22.5 Degree Chamfer with 3/16 D Ball Bearing x 1/2 D x 1/2 CH x 1/4 Inch SHK Carbide Tipped Router BitMore infoAmana ToolMR0107$38.15$28.61
Qty:
25°3/4-1/41/4-2-3/322Lower47706-
Amana Tool 47202 Carbide Tipped Bevel Laminate Trim 25 Deg Angle x 23/23 D x 9/32 CH x 1/4 Inch SHK w/ Ball Bearing Router BitMore infoAmana Tool47202$31.20$23.40
Qty:
25°3/4-27/641/4-2-3/642Lower47702-
Amana Tool 47206 Carbide Tipped Bevel Laminate Trim 25 Deg Angle x 3/4 D x 7/16 CH x 1/4 Inch SHK w/ Ball Bearing Router BitMore infoAmana Tool47206$36.40$27.30
Qty:
45°9/163/161/41/43/161-7/82Lower47706-
Amana Tool MR0108 Miniature 45 Degree Chamfer with 3/16 D Ball Bearing x 9/16 D x 1/4 CH x 1/4 Inch SHK Carbide Tipped Router BitMore infoAmana ToolMR0108$37.80$28.35
Qty:
45°1-1/16-9/321/4-22Lower47706-
Amana Tool 47204 Carbide Tipped Bevel Laminate Trim 45 Deg Angle x 1-1/16 D x 9/32 CH x 1/4 Inch SHK w/ Ball Bearing Router BitMore infoAmana Tool47204$36.40$27.30
Qty:
Note: Tool #47206 has a 3/8" diameter bearing for closer inside corner cutting.
Replacement Bearing: Use bearing #47715 after re-sharpening.

This is a steel-bodied, carbide-tipped bit for bevel trimming laminate with a standard router.
The solid construction reduces vibration for the smoothest cut possible with a two-flute bit. These bits are perfect for small fine work such as signs, lettering, small boxes, guitarmaking/luthier and toymaking; essentially any project that requires tiny flush trimming or shaping.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2021 Toolstoday. All rights reserved.