CNC Polycrystalline Diamond (PCD) Compression Router Bit Up/Down Shear with Carbide Plunge Point RH Rotation

Priced From
$134.96
-
$198.41
Free shipping on orders $49 and up
SEE OPTIONS BELOW
$149.95
$134.96
BUY 5 OF THE SAME SAVE 5%
Discount applied in your shopping cart
BUY 10 OF THE SAME SAVE 10%
Discount applied in your shopping cart
*Sort the Table by clicking on the Column Heading
DBdL# of bladesL1RotationMax RPMBrandTool NoOur PriceWish ListReady To Buy
3/81-1/43/831+11-1/2Up-Down24,000
Amana Tool DRB-192 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 3/8 D x 1-1/4 Inch CH x 3/8 SHK Router BitMore infoAmana ToolDRB-192$149.95$134.96
Qty:
1/211/22-3/41+11-3/8Up-Down30,000
Amana Tool DRB-200 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 1/2 D x 1 Inch CH x 1/2 SHK Router BitMore infoAmana ToolDRB-200$170.35$153.32
Qty:
1/21-3/81/23-3/41+11-3/4Up-Down30,000
Amana Tool DRB-208 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 1/2 D x 1-3/8 CH x 1/2 Inch SHK Router BitMore infoAmana ToolDRB-208$176.00$158.40
Qty:
5/811/22-7/81+11-3/8Up-Down27,000
Amana Tool DRB-212 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 5/8 D x 1 Inch CH x 1/2 SHK Router BitMore infoAmana ToolDRB-212$188.95$170.06
Qty:
5/81-5/85/841+11-3/4Up-Down27,000
Amana Tool DRB-216 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 5/8 Dia x 1-5/8 Cut Height x 5/8 Shank Router BitMore infoAmana ToolDRB-216$209.95$188.96
Qty:
3/41-3/83/43-3/41+12Up-Down18,000
Amana Tool DRB-224 Polycrystalline Diamond (PCD) Tipped Compression Up/Down Shear R/H Direction 3/4 D x 1-3/8 CH x 3/4 SHK Router BitMore infoAmana ToolDRB-224$220.45$198.41
Qty:
Note:
#DRB-228 and #DRB-232 are replaced by #DRB-224

For CNC Use Only!

Diamond is the hardest material on the earth. Polycrystalline Diamond (PCD) tooling is manufactured in a high-temperature and high-pressure laboratory that fuses diamond particles onto a carbide substrate, which allows the diamond to be brazed onto a tool body.

PCD Tooling Benefits:

  • Harder cutting edge provides higher resistance to wear
  • Cut thousands of feet more than carbide without changing tool, saving setup time
  • Optimized machine tool efficiency
  • Quality of finish is often significantly improved
If you’re looking for the ultimate in tooling, you’ve found it! Amana Tool®'s PCD tipped compression CNC router bits will groove, joint and rabbet a wide variety of tough, abrasive materials including composites, particleboard, MDF (both raw or with melamine), veneer and hardwoods. The cutting edge lasts much longer than carbide for extremely long life. Depending on the material being cut, PCD tooling has been known to out perform a carbide tool by a ratio of 300:1. However, to be conservative in your buying decision, we suggest you base your expectations on 25:1 ratio over carbide tooling.

Excellent for cutting:

  • Aluminum
  • Aluminum Composite Material (ACM)
  • Composite panels
  • Custom composite materials
  • Fiberglass
  • Fiberglass PCB board
  • Fiber-reinforced urethane
  • Fiber-reinforced structural foam floors
  • Lightweight composites
  • MDF
  • Plywood
  • Plastic
  • Hard and soft wood


Multipliers for different materials:

Chipboard without coating: Max RPM x 1.1%

Cross grain veneer: Max RPM x 0.7%

MDF: Max RPM x 0.8%
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2021 Toolstoday. All rights reserved.