Cove with Ball Bearing Guide Router Bits - Economy

Priced From
$21.63
-
$49.46
Free shipping on orders $49 and up
SEE OPTIONS BELOW
*Sort the Table by clicking on the Column Heading
RDBdLFluteBall BearingReplacement BearingBrandTool NoOur PriceWish ListReady To Buy
1/47/81/21/422Lower47704
Timberline 220-10 Carbide Tipped Cove 1/4 R x 7/8 D x 1/2 CH x 1/4 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-10$30.90$21.63
Qty:
1/47/89/161/22-3/82Lower47704
Timberline 220-26 Carbide Tipped Cove 1/4 R x 7/8 D x 9/16 CH x 1/2 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-26$33.95$23.77
Qty:
3/81-1/81/21/422Lower47704
Timberline 220-14 Carbide Tipped Cove 3/8 R x 1-1/8 D x 1/2 CH x 1/4 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-14$32.10$22.47
Qty:
3/81-1/89/161/22-29/642Lower47702
Timberline 220-30 Carbide Tipped Cove 3/8 R x 1-1/8 D x 9/16 CH x 1/2 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-30$33.20$23.24
Qty:
1/21-3/85/81/42-1/42Lower47704
Timberline 220-18 Carbide Tipped Cove 1/2 R x 1-3/8 D x 5/8 CH x 1/4 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-18$37.35$26.15
Qty:
1/21-3/83/41/22-41/642Lower47702
Timberline 220-34 Carbide Tipped Cove 1/2 R x 1-3/8 D x 3/4 CH x 1/2 Inch SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-34$37.20$26.04
Qty:
3/4211/22-7/82Lower47704
Timberline 220-38 Carbide Tipped Cove 3/4 R x 2 Inch D x 14 CH x 1/2 SHK w/ Lower Ball Bearing Router BitMore infoTimberline220-38$70.65$49.46
Qty:
Use these cove bits to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. The other half is the corner-round. 

  • Large-diameter tools must be run at reduced speed.
  • Bits with above 2" diameter are not guaranteed due extreme diameters.
  • Use in hand-held or table-mounted routers.
For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish, and it will prolong tool life.

View DXF CNC FileDownload DXF tool file (limited items currently)

View PDF CNC FileDownload PDF tool file (limited items currently)

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Copyright © 2021 Toolstoday. All rights reserved.